Trlon air conditioner manufacturers have silent cooling towers, closed cooling towers and cooling tower noise reduction, maintenance and transformation services.
National Service Hotline National Service Hotline:

4008-8383-95

Your current location:HOME > News > FAQ

FAQ

The steps of repairing and anti-corrosion construction method of cooling tower chassis

Author:Trlon  Views:  Time:2021-08-06
The steps of repairing and anti-corrosion construction method of cooling tower chassis

  Cooling water tower anti-corrosion, steel structure anti-corrosion, sewage pool glass fiber reinforced plastic anti-corrosion, furnace frame anti-corrosion, pipeline anti-corrosion insulation, wind turbine tower anti-corrosion (cleaning, spraying, maintenance), various iron tower anti-corrosion, cooling tower anti-corrosion (platform , Straight climbing ladder, protective net), anti-corrosion of storage tank. New cooling tower platforms, signal lights assembly and replacement, cooling tower assembly straight ladders and other high-altitude operations projects have a pass rate of %. In recent years, trlon has excellently completed many project repairs and renovations.M0bCooling tower noise reduction treatment manufacturer

  Waterproof plugging construction steps for cooling tower chassis:M0bCooling tower noise reduction treatment manufacturer

  1. Preparations before the cooling tower waterproof plugging and bonding:M0bCooling tower noise reduction treatment manufacturer

  ①The bonding place must be dust-free and not wet and cold;M0bCooling tower noise reduction treatment manufacturer

  ②The blending of epoxy resin and hardener: 1Kg is suitable for each time, and it cannot be higher than 2Kg. After using it, adjust and use again. The percentage is 1Kg epoxy resin. Use 10cc hardener.M0bCooling tower noise reduction treatment manufacturer

  2, Cooling tower waterproof plugging and bonding method:M0bCooling tower noise reduction treatment manufacturer

  First use a brush to coat the blended epoxy resin, then paste the glass fiber, and then coat the epoxy resin, repeat two to three times.M0bCooling tower noise reduction treatment manufacturer

  3. Common precautions for waterproofing and plugging cooling towers:M0bCooling tower noise reduction treatment manufacturer

  ①It takes 6 hours for the adhesive to be applied, and no pressure or trampling is allowed;M0bCooling tower noise reduction treatment manufacturer

  ②The glass fiber should not be wet or cold before application. If it is wet or cold, it must be dried before it can be used.M0bCooling tower noise reduction treatment manufacturer

  The above is the reason for the leakage of the cooling tower chassis and the repair method. I hope to help everyone. Therefore, everyone needs to fully consider this before construction to avoid many unnecessary problems in the middle and late stages.M0bCooling tower noise reduction treatment manufacturer

  Square cooling tower anti-corrosionM0bCooling tower noise reduction treatment manufacturer

  Cooling tower anti-corrosion construction steps:M0bCooling tower noise reduction treatment manufacturer

  A. Fix the leaves of the exhaust fan with hemp rope at the upper end of the cooling tower to prevent the leaves from rotating and causing injuries to employees.M0bCooling tower noise reduction treatment manufacturer

  B. Take a ladder to enter the cooling tower from the exhaust fan at the upper end of the cooling tower, disassemble the old packing inside one by one, and place it according to the point selected by Party A.M0bCooling tower noise reduction treatment manufacturer

  C. Clean the inner and outer walls of the cooling tower, and the surface of the supporting steel frame inside shall be treated with rust prevention, and Party A shall be notified whether the corroded steel frame needs to be replaced according to the corrosion status, and the assembly screws are firm.M0bCooling tower noise reduction treatment manufacturer

  D. Check each sprinkler device, and replace it according to the situation. Note: The spray device is brought by Party A.M0bCooling tower noise reduction treatment manufacturer

  E. Water basin and cooling tower shell are used for leak-proof maintenance.M0bCooling tower noise reduction treatment manufacturer

  F. Brush the anti-rust paint on the steel frame more than 2 times.M0bCooling tower noise reduction treatment manufacturer

  G. After the paint is dry, assemble the new filler in the cooling tower.M0bCooling tower noise reduction treatment manufacturer

  China trlon air conditioner focuses on the product research and development, design, production, sales, assembly, cooling tower maintenance and refrigeration engineering of central air conditioning cooling equipment. Cooling tower maintenance and transformation related services include: contracting major brands of cooling tower filler replacement, cooling tower dismantling and replacement, cooling tower parts replacement, cooling tower sound insulation and noise reduction, cooling tower anti-corrosion and waterproof plugging, cooling tower maintenance, circulating water Cooling system engineering, etc. The service scope covers Dongguan, Shenzhen, Guangzhou, Huizhou, Foshan, Zhuhai, Zhongshan, Shantou and other places, and is committed to building a high-quality cooling system and supporting facilities service project manufacturer.M0bCooling tower noise reduction treatment manufacturer

Article Address:https://www.trlen.com/baike/482.html

Colored Contact Form

Get the latest information and prices of cooling towers? We will reply as soon as possible within 24 hours

( Items with * are required)

*name
Company
*Phone
*Message

News

Contact

Guangdong Trlon Energy-saving Air Conditioning Equipment Co., Ltd.

Contact:Mr. Wang

Free Hotline:4008-8383-95

Company Email:sales@trlon.com

Web Site:https://www.trlen.com/

Company Address: 1916A, Block A, David Donglong Business Building, Longhua, Longhua District, Shenzhen

Trlon WechatClose
alibaba